LED FLY Instructions


Delivery balloons

LED FLY BALLOON ON STICK

Easy step-by-step guide to assembling your Led Fly Balloons

Step 1: carefully remove the transparent balloon from the box. It is located under the led light string.

** Although the balloon may look small, it will expand to 18/24 inches after inflating. **

Step 2: expand the balloon to make it flat.

Step 3: gently pull the balloon in the horizontal direction.

Step 4: lightly pull the balloon in a vertical direction (this is just to smooth out any wrinkles).

* Keep the surface of the balloon flat *

** If you accessorize your balloon with feathers, now that you will fill it. **

Step 5: inflate the ball with ordinary air or air pump until all wrinkles disappear. The seams should be smooth.

Step 6: stop inflation when the inflatable range is about 16 inches (for 18 inch balloon)(through balloon, not around balloon) (+/- 2 inches). Stop inflation when the inflatable range is about 22 inches (for 24 inch balloon) (through balloon, not around balloon) (+/- 2 inches). The balloon will be full and round.

Step 7: using your hand, twist and turn the neck of the balloon. Step 8: make a knot on the neck of the balloon with the extended tail to prevent the filled air from the tank.

Step 9: Untangle the led strip and slide your fingers all over the tape to make it smooth. 

 Step 10: Slide the led strip inside the stick.

*** If you apply a sticker on a balloon, now, when you apply it.***

Step 11: wrap the led light cord around the outside of the balloon.

** If you add tape to your balloon, now that you decorate it **

Wrap a string of Led light

Led Fly Balloon can be wrapped in several different ways. Keep in mind that the more you wrap them, the better they will glow!

Wrap 1 Time

Start at the base of the ball where the knot is. Unravel the led strip by simply sticking your thumb in the center and giving it an untwirl. With the battery end on the ground, squeeze the open end of The led light strip. Leave roughly 1/2 inch of open wire, and twist the Led wire twice around the knot, right at the base of the balloon. After twisting twice, follow the swirling line all the way around the balloon until you return back to the base where the knot is. Once you reach the base of the balloon, double turn the led light around the knot and here you go!

To Wrap 2 Times

Start at the base of the ball where the knot is. Unravel the led strip by simply inserting your thumb in the center and giving it an untwirl. With the battery end on the ground, squeeze the open end of the led light string. Leave roughly 1/2 inch of open wire, and twist the led light cord twice around the knot, right at the base of the balloon. After twisting twice, follow the seamed line all the way around the balloon until you return back to the base of the balloon where the knot is. When you reach the node, turn the led light string once around the node and go down the other side of the balloon (as if you were doing a cross). Once you reach the base of the balloon, turn the led light string twice around the knot and here you go! Turn one led string and start lighting!

The User Of The Pen

Take the funnel and insert it into the neck of the cylinder. Place the feathers (pair at a time)directly into the funnel. As soon as the feathers will be inside the funnel, take a stick (stick works well) and push the feathers in the lower part of the funnel. You will see the feathers slide their way into the balloon. Once all the feathers are inside, fill them with helium or air.

Etiquette Instructions

Put a balloon (its seam) on something so that it is nice and straight in front of you. Separate the sticker only slowly (on the paper part of the substrate, and the tracing paper sticky side that you need to write to stay on). You are left with a sticker (sticky side) ready to work on the balloon.

Place the sticker in the balloon position where you are most happy with it. Wipe it nice and smooth on the balloon with your fingers. Then you will be slowly sawing, from one corner, keeping it nice and sharp as a razor as you are exfoliating (this is what helps nicely letters stay in position). Keep clearing all the way to the other side.

The User Of The Tape

Unroll the led strip by simply removing the knot .

** Remember that the more accessories you place inside the balloon, the more it will weigh.

Delivery balloons

LED FLY HELIUM BALLOON 

Step 1: Carefully remove the transparent balloon from the box. It is located underneath the LED light string.

** Although the balloon might look small it WILL expand to 18/24 inches once inflated. **

Step 2: Unfold the balloon to make it flat.

Step 3: Lightly pull the balloon in the horizontal direction.

Step 4: Lightly pull the balloon in the vertical direction (This is just to smooth out any wrinkles).

* Keep the surface of the balloon flat *

** If you are accessing your balloon with feathers, now is when you will fill it. **

Step 5: Inflate the balloon by either using a helium tank or an air pump, until all of the wrinkles disappear. The seas should be smooth.

Step 6: Stop the inflation when the inflatable range is about 16 inches (for the 18 inch balloon)(across the balloon, not around the balloon) (+/- 2 inches). Stop the inflation when the inflatable range is about 22 inches (for the 24 inch balloon)(across the balloon, not around the balloon) (+/- 2 inches). The balloon will be full and round.

Step 7: Using your hand, twist and turn the neck of the balloon.

Step 8: Make a knot in the neck of the balloon with its extended tail, to prevent the filled air from flowing out.

*** If you are applying a decal to your balloon, now is when you will apply it.***

Step 9: Wrap the LED light string around the outside of the balloon.

** If you are adding ribbon to your balloon, now is when you will garnish it **

Wrapping the LED Light String

Balloominators can be wrapped several different ways. Keep in mind that the more you wrap them, the shorter its tail will be!

To Wrap 1 Time

Start at the base of the balloon, where the knot is. Unravel the LED strip by simply sticking your thumb through the center and letting it untwirl. With the battery end on the ground, grip the open end of the LED light strip. Leave roughly 1/2 an inch of open wire, and twist the LED wire twice around the knot, right at the base of the balloon. After twisting twice, follow the seamed line all the way around the balloon, until you return back to the base, where the knot is. Once you reach the base of the balloon, twist the LED light twice around the knot, and there you go!

To Wrap 2 Times

Start at the base of the balloon, where the knot is. Unravel the LED light strip by simply sticking your thumb through the center and letting it untwirl. With the battery end on the ground, grip the open end of the LED light string. Leave roughly 1/2 an inch of open wire, and twist the LED light string twice around the knot, right at the base of the balloon. After twisting twice, follow the seamed line all the way around the balloon, until you return back to the base of the balloon, where the knot is. When you reach the knot, twist the LED light string once around the knot and travel down the other side of the balloon (as if you were making a cross). Once you reach the base of the balloon, twist the LED light string twice around the knot, and there you go! Turn one the LED light string and let the illumination begin!

Feather Instructions

Take a funnel, and insert it into the balloon's neck. Place feathers (a couple at a time) straight down into the funnel. Once the feathers are inside the funnel, take a stick (a chopstick works well), and push the feathers into the bottom of the funnel. You will see the feathers slide their way into the balloon. Once all of the feathers are inside, fill up with either helium or air.

Decal Instructions

Rest the balloon (its seam) on something so that it is nice and straight in front of you. Peel the decal apart slowly (the paper part is the backing, and the tracing paper is the sticky side, which is what you need the writing to stay on). You are left with the decal (sticky side) ready to go on the balloon.

Place the decal into position on the balloon, wherever you are most happy with it. Rub it nice and smooth onto the balloon with your fingers. Then you are going to slowly peel, from one corner, keeping it nice and razor sharp as you are peeling back (this is what helps the letters stay nicely in position). Keep on peeling all of the way to the other side.

** Be mindful that the more accessories you place inside the balloon the more your it will weigh, which can cause it to not float as high.**

Close
Shopping Cart
Your Cart is Empty